Mon–Sat 8AM–5PM · Emergency SundayClick to call: (812) 473-3536
A-1 Lock & Safe Co.
Full-service locksmithServing Evansville & the Tri-State since 1983
Call now for fastest response(812) 473-3536After hoursOpen now
After hours · Call for availabilityOpen now · Mon–Sat 8AM–5PM

Strike Plates & Three-Inch Screws: Where a Forced Door Holds or Gives

When a locked door is forced, the deadbolt usually stays in one piece and the thin wood around the strike plate gives way. The short screws holding most strikes reach only the door jamb. A reinforced strike fastened with three-inch screws ties the bolt into the wall framing, using inexpensive hardware.

Open the front door and find the strike plate on the frame, where the deadbolt slides in. Count its screws. Back one out and look at its length. Most doors are hung with three-quarter-inch or one-inch screws. That length ends in the jamb board lining the opening. Behind the jamb is a narrow gap, a few wood shims, and then the framing stud beside the opening.

Why the frame gives before the lock

When the Bureau of Justice Statistics studied household burglaries, it found that damaging or removing a door was the most common way in when force was used or attempted. Police crime-prevention advice traces that damage to the strike and the thin wood holding it. The steel bolt seldom fails.

Consumer Reports tested almost two dozen deadbolts with the hardware they came with. Only six resisted repeated impacts. A box strike held by longer screws gave the locks a far stronger hold on the door.

What a reinforced strike & long screws change

Long screws move the load from the jamb to the house framing. A three-inch screw passes through the strike, the jamb, and the gap behind it. Then it bites into the stud. The King County Sheriff’s Office in Washington recommends a heavy-duty, four-screw strike with three-inch screws on a wood frame. Compared with a standard plate, a reinforced strike has:

  • More screws. Four or more holes, so no single screw carries the load.
  • A longer plate. The force spreads along more of the jamb.
  • A metal box. A steel cup lines the hole the bolt sits in, so the bolt bears on metal.

Not every hole on a strike lines up with the stud. A screw that misses it holds only in the jamb, like the short one it replaced. Leave that hole at its original length and put the long screws in the holes that grip.

Long screws in the hinges

Once the strike is fastened to the framing, the short hinge screws on the other edge of the door are the weakest point left. Swap at least one frame-side screw in each hinge for a three-inch screw. Its head should sit flush. The hinge screws nearest the doorstop molding can reach the stud, while the ones near the hinge pin may catch only drywall.

In the top hinge, a long screw also lifts a sagging door. That is useful on a door that drags, but it means every hinge screw can move the door a little. Check the deadbolt after each one goes in.

Which doors to do first

Start with every outside door that has a deadbolt. That means the front and back doors, a side door, and the door from the garage into the house. Treat that last one as an outside door. When the overhead door is left up, it is the only locked door between the driveway and the house. If you just moved in, add the strikes to your first-day lock checklist while the doors are open for the rekey.

Knob-only doors gain less from a strike upgrade. The latch on a knob is short and angled, and it sits in a shallow strike. Fit a deadbolt on that door first. A pair of French doors or a slider needs hardware made for it, so ask before you buy a strike kit for one.

Doing it yourself

Long screws in the existing strike need a drill, a pilot bit, and the screws. A reinforced strike needs a bigger recess. Its plate is longer and its box sits deeper, so the jamb has to be chiseled out first. Trace the new plate and box on the jamb and cut only to that outline. Every extra cut removes wood the screws need. Set the new strike with short screws first, then swap them for long ones. Work one screw at a time so you can tell which one changed the fit.

  1. Throw the deadbolt with the door open. It should slide all the way out without catching. Remember how it feels.
  2. Take out one short screw. Leave the others in so the plate stays put.
  3. Drill a pilot hole. Use a bit as wide as the solid core of the screw under its threads. Too large a hole strips. No hole at all can split a dry jamb.
  4. Snug the screw, then stop. Drive it until the head seats in the plate. Close the door and lock it before you move to the next screw.
  5. Watch the fit. A long screw pulls the jamb toward the stud. Drive it too far and the latch may stop catching, the door may rattle when shut, or a twisted jamb can make the bolt rub the edge of the strike. Back the screw out a turn or two. If the gap behind the jamb is wide, pull the trim and set a shim between the jamb and the stud, level with the strike. If the bolt still drags, our post on a deadbolt that is hard to lock shows how to find where it hits. Then repeat from step two for the next screw.

Buy screws with heads that fit the countersunk holes in your strike. A head that sticks up can scrape the bolt.

Doors where screws are not enough

Long screws need sound wood to bite into. Stop and call when you find any of these.

  • The jamb is split, soft, or patched with filler around the strike.
  • The strike recess has been chiseled out so many times that the plate no longer sits on solid wood.
  • The door edge is cracked around the deadbolt.
  • The door sits in a steel frame, or the frame is set straight into brick or block.
  • The deadbolt stops short of full travel, even with the door open.
  • A long screw spins and will not tighten.

A door that has been forced before can have a cracked jamb behind the trim. Repairing that is partly carpentry. We will tell you on the phone if the frame needs a carpenter before we can reinforce it.

What we do on a house call

Strike work is part of our residential locksmith service, and we look at the strike screws when we rekey a house. We have reinforced strikes on Evansville-area doors since 1983. On a reinforcement visit, we first confirm the bolt reaches full travel. That comes before any screw. Then we fit a reinforced strike with screws long enough to reach the stud and set long screws in the hinges. Where a long screw draws the jamb in, we shim between the jamb and the stud. The last check is the deadbolt, thrown with the door shut.

If your deadbolt turns smoothly and is not worn, our guide to rekeying or replacing your locks explains why it can stay. When you call A-1 Lock & Safe, tell us how many outside doors have deadbolts and what the frames are made of. We work Monday through Saturday, eight to five. On a Sunday, call and ask what is available.

Related pages

Questions we hear

Do I need a new deadbolt to make my door harder to force?

Usually not. Replace the deadbolt only if it is worn, wobbles in the door, or will not extend all the way. Otherwise the money goes further on the strike and the screws.

Are three-inch screws enough without a new strike plate?

They help on their own, as long as at least one reaches the stud. If the old strike has only two holes and no metal box behind the opening, replace it at the same time. A four-hole strike lets you put more than one long screw into the framing.

Do long screws help a steel or fiberglass door?

Yes, when the frame is wood. Most steel and fiberglass doors still hang in a wood frame, and every strike screw goes into that frame. A steel frame needs different screws and anchors.

Ready when you are

Call us and see how we can help.

Call now for fastest response(812) 473-3536One number, answered here in town.
After hoursOpen now
Monday–Friday8AM–5PM
Saturday8AM–5PM
SundayCall for availability
Emergency lineOpen now(812) 473-3536
Call now